Betekenis van:
fuel injection system

Voorbeeldzinnen

1. Fuel injection system (diesel engines):
2. By fuel injection [2] Specify the tolerance. : system description
3. Feed system (pump, injection into intake, mixing with fuel, etc.):
4. Feed system (by pump/injection into intake/mixing with fuel, etc.)
5. The fuel-injection system electronic, fuel quantity and timing actuator(s) for circuit continuity (i.e. open circuit or short circuit) and total functional failure.
6. the fuel-injection system electronic, fuel quantity and timing actuator(s) for circuit continuity (i.e. open circuit or short circuit) and total functional failure.
7. The fuel temperature shall be measured at the inlet to the carburettor or at the fuel injection system and maintained within the limits established by the engine manufacturer.
8. The fuel-injection system electronic fuel quantity and timing actuator(s) is/are monitored for circuit continuity and total functional failure;
9. Line costs (including checking of the electrical system, the avionics and the landing gear and inspection of the fuel injection system)
10. Feed system (by pump/injection into intake/mixing with fuel, etc.) [6] Delete where not applicable (there are cases where nothing needs to be deleted when more than one entry is applicable).
11. .13 Components of a diesel engine fuel system shall be designed considering the maximum peak pressure which will be experienced in service, including any high pressure pulses which are generated and transmitted back into fuel supply and spill lines by the action of fuel injection pumps.
12. .16 Existing class B ships shall comply with the requirements of paragraphs .2.9 to .2.11, except that a suitable enclosure of engines having an output of 375 kW or less having fuel injection pumps serving more than one injector may be used as an alternative to the jacketed piping system in paragraph .2.9.
13. Lubricant temperature: minimum: K maximum: K4.1.16. Pressure charger: yes/no (1)4.1.16.1. Make:4.1.16.2. Type:4.1.16.3. Description of the system (e.g. maximum charge pressure, waste-gate, if applicable):4.1.16.4. Intercooler: yes/no (1)4.1.17. Intake system: maximum allowable intake depression at rated engine speed and at 100 % load: kPa4.1.18. Exhaust system: maximum permissible exhaust back pressure at rated engine speed and at 100 % load: kPa4.2. Additional anti-pollution devices (if any, and if not covered by another heading)Description and/or (1) diagram(s):4.3. Fuel feed4.3.1. Feed pumpPressure (2) or characteristic diagram: kPa4.3.2. Injection system4.3.2.1. Pump4.3.2.1.1. Make(s):4.3.2.1.2. Type(s):4.3.2.1.3. Delivery: mm3 (2) per stroke or cycle at pump speed of: r/min (rated)and r/min (maximum torque) respectively, or characteristic diagramState which method used: on engine/on pump bench (1)4.3.2.1.4. Injection advance4.3.2.1.4.1. Injection advance curve (2):4.3.2.1.4.2. Timing (2):4.3.2.2. Injection piping4.3.2.2.1. Length: mm4.3.2.2.2. Internal diameter: mm4.3.2.3. Injector(s)4.3.2.3.1. Make(s):4.3.2.3.2. Type(s):4.3.2.3.3. Opening pressure (2) or characteristic diagram (1):4.3.2.4. Governor(s)
14. Pressure charger: yes/no (1)3.4.1.16.1. Make:3.4.1.16.2. Type:3.4.1.16.3. Description of the system (e.g. maximum charge pressure, waste-gate, if applicable):3.4.1.16.4. Intercooler: yes/no (1)3.4.1.17. Intake system: maximum allowable intake depression at rated engine speed and at 100 % load: kPa3.4.1.18. Exhaust system: maximum permissible exhaust back pressure at rated engine speed and at 100 % load: kPa (2)3.4.2. Additional anti-pollution devices (if any, and if not covered by another heading)Description and/or diagram(s):3.4.3. Fuel feed3.4.3.1. Feed pumpPressure (2) or characteristic diagram: kPa3.4.3.2. Injection system3.4.3.2.1. Pump3.4.3.2.1.1. Make(s):3.4.3.2.1.2. Type(s):3.4.3.2.1.3. Delivery: and mm3 (2) per stroke or cycle at pump speed of:r/min (rated) and r/min (maximum torque) respectively, or characteristic diagramState which method used: on engine/on pump bench (1)3.4.3.2.1.4. Injection advance3.4.3.2.1.4.1. Injection advance curve (2):3.4.3.2.1.4.2. Timing (2):3.4.3.2.2. Injection piping3.4.3.2.2.1. Length: mm3.4.3.2.2.2. Internal diameter: mm3.4.3.2.3. Injector(s)3.4.3.2.3.1. Make(s):3.4.3.2.3.2. Type(s):3.4.3.2.3.3. Opening pressure (2) or characteristic diagram (1):